Fracture and Structural Integrity: The Podcast

Fracture and Structural Integrity: The Podcast@fis_podcast

0 followers
Follow
Effect of core architecture on flexural strength and failure behavior of additively manufactured composite sandwich panels
S79:E19

Effect of core architecture on flexural strength and failure behavior of additively manufactured composite sandwich panels

https://doi.org/10.3221/IGF-ESIS.79.14 The development of highly porous structures that combine low weight with high mechanical performance is one of the key challenges in modern materials science and mechanical engineering. This challenge is particularly relevant to the design of sandwich structures for aerospace, automotive, and other industrial applications, where high specific strength and stiffness are required. A promising approach to addressing this challenge is the use of mechanical metamaterials as cores of sandwich panels. In this study, a comparative investigation was conducted into the effect of core architecture on the mechanical behavior and failure mechanisms of additively manufactured composite sandwich panels made of polylactic acid (PLA) and polyamide 6 reinforced with 30 wt.% carbon fibers (PA6+CF30) under three-point bending. Cores designed based on two-dimensional and three-dimensional unit cells were considered. The apparent flexural modulus and maximum flexural stress of the structures were determined. The failure process was analyzed using a digital image correlation system. In addition, numerical simulations were performed to investigate the stress state and predict the regions of failure initiation. The maximum flexural stress of sandwich panels with a three-dimensional core design was, on average, 3.8 times higher than that of panels with a two-dimensional core design. Analysis of the maximum principal stress-fields demonstrated the potential of numerical simulations for predicting failure initiation zones, which coincided with the experimentally observed damage regions. The obtained results can be used in the design of lightweight, high-strength sandwich structures with prescribed deformation and failure scenarios.

Nonlinear dynamics of thermal shock in graphite
S79:E18

Nonlinear dynamics of thermal shock in graphite

https://doi.org/10.3221/IGF-ESIS.79.13 The transition to combustion of carbon materials in components of rocket and space technology is preceded by intensive heating from the surface, which can be accompanied by the initiation of a stress wave (thermal shock) with subsequent ablation, delamination, or spalling. The heating rate and the nonlinear dependence of thermal diffusivity on temperature, which depends on the porosity of the carbon material, determine the possibility of the effect of heat localization in the blow-up mode. The research is devoted to the analysis of the patterns of heat localization and its connection with the mechanisms of thermal shock in graphite under intense thermal exposure. Assessing the thermal strength of the material under conditions of heat localization generally requires solving a wave problem as the defect development time approach acoustic times using specific criteria. An approach to the numerical modeling of the nonlinear heat conduction problem is presented, taking into account the dependence of thermophysical and physicomechanical properties on temperature. The boundary conditions for the emergence of blow-up modes are defined, and the dynamics of heat localization are investigated. A comparison of numerical results with an analytical solution is carried out, which confirms the transition between two modes of heat propagation: a blow-up mode and a wave mode. The numerical estimate of the damage depth under a single thermal pulse is consistent with known experimental data.

Corrosion morphology and penetration in high-strength structural steels characterized by X-Ray tomography and mass-loss measurem
S79:E17

Corrosion morphology and penetration in high-strength structural steels characterized by X-Ray tomography and mass-loss measurem

https://doi.org/10.3221/IGF-ESIS.79.12 Mass-loss measurements provide a global measure of corrosion damage but do not capture extreme localized penetration. This study compares CT-derived maximum localized penetration with mass-loss-derived equivalent average penetration for S460, S690, and S960 structural steels subjected to three controlled 5% salt-spray exposure regimes. X-ray computed tomography was performed on one specimen per steel-grade–exposure combination, while gravimetric measurements were obtained from four comparable specimens per condition. The novelty lies in directly comparing localized CT descriptors with replicated global mass-loss data under common exposure conditions. Maximum localized penetration ranged from 97.5 to 724.2 µm, whereas equivalent average penetration ranged from 16.3 to 49.7 µm. The results show that CT and gravimetric measurements describe different aspects of corrosion damage and should not be used interchangeably. A corrosion localization index was used only as a supplementary maximum-to-average penetration ratio. Combining both descriptors may improve durability assessment where average mass loss underrepresents severe localized penetration.

Machine learning–based wear prediction of carbon fiber–reinforced polypropylene composites using an L25 orthogonal array
S79:E16

Machine learning–based wear prediction of carbon fiber–reinforced polypropylene composites using an L25 orthogonal array

https://doi.org/10.3221/IGF-ESIS.79.11 Applications of lightweight, wear-resistant polymer composites in automobile and engineering fields require an effective method for predicting and optimizing their wear performance, which will also curtail the time for designing new materials. Therefore, the present work employs L25 orthogonal array, machine learning (ML) techniques and wear mapping to study the dry sliding wear behavior of short carbon fiber–reinforced polypropylene (CF/PP) composites. Wear loss of the CF content (5–20 wt. %), applied load, sliding velocity and sliding distance were systematically investigated. The governing wear mechanisms were explained by using microstructural and worn surface analyses. The results show that the use of CF reinforcement changes the prevailing wear-mode from severe adhesive wear and plastic deformation in neat PP to stable micro-abrasive wear due to heat softening and crack initiation and propagation being prevented. Composites with 10–15 wt. % CF had the best wear resistance because the interfacial bond, matrix continuity, and reinforcing efficiency complemented the best. Of the other factors examined, Analysis of Variance revealed that wear loss was strongly impacted by all four parameters ). The most significant contribution was from load (32.88%), followed by sliding distance (15.20%), sliding velocity (21.89%), and fiber content (26.17%). Transition between mild and severe wear regimes, under different operating conditions, was identified with the use of wear maps. The developed and compared four ML algorithms are: K-Nearest Neighbors, Random Forest, Decision Tree, and Support Vector Machine (SVM). The SVM model showed the best accuracy of prediction (R² = 0.9362), which can be used to predict the wear and is used as a strong tool for the design and optimization of wear resistant CF/PP composite.

Heat treatment optimization and Chromium Nitride precipitation control in heavy-section Superduplex Stainless Steel forgings
S79:E15

Heat treatment optimization and Chromium Nitride precipitation control in heavy-section Superduplex Stainless Steel forgings

https://doi.org/10.3221/IGF-ESIS.79.10 The optimization of mechanical properties in superduplex stainless steel forgings requires precise control of phase balance and precipitation kinetics. This study investigates the effect of different heat treatment routes, including single- and double-step solution annealing and varying cooling rates, on Cr nitride precipitation and secondary austenite formation in S32760 superduplex stainless steel. Mechanical and corrosion properties were assessed through Charpy impact, tensile, Vickers hardness, and pitting corrosion tests, complemented by optical and SEM microstructural characterization. Unlike the heat treatment, the radial sampling position within the investigated forged component did not significantly affect the measured properties. While pitting corrosion resistance remained unaffected, impact toughness was highly sensitive to the thermal treatment. A single-step treatment at 1120 °C caused severe embrittlement due to extensive Cr nitride precipitation, whereas a second solution annealing step at 1060 °C was necessary to restore toughness. Its effectiveness, however, depended strongly on the cooling rate applied after the first step. Microstructural analysis revealed that slower cooling after the first holding phase promotes coarser nitrides, which act as nucleation sites for secondary austenite during the second annealing stage, enhancing N absorption and limiting subsequent nitride precipitation. Conversely, rapid cooling reduces both nitride and secondary austenite formation, favoring renewed nitride precipitation during final cooling. These results highlight the initial cooling rate as the key parameter governing the effectiveness and reliability of two-step heat treatment for large-scale superduplex components.

Modeling the PSN mechanism of recrystallization nuclei formation in Inconel 718
S79:E14

Modeling the PSN mechanism of recrystallization nuclei formation in Inconel 718

https://doi.org/10.3221/IGF-ESIS.79.09 This study proposes and applies a mathematical model to describe the process of recrystallization nucleation on large -phase particles in the Inconel 718 nickel alloy during annealing (the particle stimulated nucleation (PSN) mechanism). The investigation employs a multilevel approach based on an extended statistical model, in which the subgrain structure is explicitly described by an aggregate of Laguerre polyhedra. The model for the formation of new recrystallized grain nuclei is based on the physical mechanisms of recovery: subgrain coalescence and low-angle boundary migration. Additionally, the model accounts for lattice rotations of subgrains near the non-deformable particle resulting from the incompatibility of prior plastic deformation, as well as the retarding effect of dispersed γ′ and γ″ particles during subgrain boundary migration. Numerical experiments were conducted on a representative volume of subgrains at annealing temperatures range 450–950 °C. It is shown that at 450 - 850°C subgrain growth near the -phase particle is retarded due to increased misorientation, which hinders coalescence. At temperatures above 950 °C, the dissolution of the strengthening phases γ′ and γ″ leads to a decrease in the Zener pinning force and intense boundary migration near the -phase particle results in the active formation of recrystallization nuclei. It is established that a needle-shaped -particle promotes more intense nucleation compared to a spherical one due to its larger interfacial area. The simulation results are in qualitative agreement with known experimental data.

Effects of SBR latex and glass fibers on the fracture behavior of geopolymer concrete: an empirical and computational approach
S79:E13

Effects of SBR latex and glass fibers on the fracture behavior of geopolymer concrete: an empirical and computational approach

https://doi.org/10.3221/IGF-ESIS.79.08 The quasi-brittle nature of Geopolymer Concrete (GPC) severely limits its broader structural viability. This study investigates the optimization of a Ground Granulated Blast-furnace Slag (GGBS) geopolymer concrete through sequential Styrene-Butadiene Rubber (SBR) latex modification and alkali-resistant (AR) glass fiber reinforcement. Polymer dosages from 0% to 25% were evaluated, validating a 15% SBR concentration as the microstructural baseline. Scanning Electron Microscopy and Energy Dispersive X-Ray Analysis (SEM/EDAX) confirmed that this dosage facilitates a monolithic interpenetrating polymer network and enhances Calcium Aluminosilicate Hydrate (C-A-S-H) gel precipitation. Subsequently, AR glass fibers were incorporated (0% to 2.0%) into the optimized SBR-GPC matrix. Empirical testing isolated 1.5% as the absolute optimal fiber dosage, yielding peak 28-day compressive (31.70 MPa), flexural (5.39 MPa), and bearing (62.26 MPa) capacities. Furthermore, single-point loading fracture mechanics testing revealed that the 1.5% integration maximized both fracture energy and the critical stress intensity factor, while also achieving a 50.00% enhancement in ultimate impact energy absorption and reducing chloride permeability to 1350.20 Coulombs (Low). Dosages exceeding 1.5% induced severe agglomeration, systematically degrading structural integrity. Finally, mathematical regression models were compared against advanced Machine Learning architectures like Artificial Neural Networks (ANN) and Gaussian Process Regression (GPR). While simple empirical equations reliably predicted tensile and flexural capacities, the GPR framework demonstrated exceptional superiority in mapping the non-linear compressive strength behavior, achieving a Leave-One-Out Cross-Validation of 0.950.

Probabilistic fatigue reliability assessment of girth-weld surface cracks in API 5L X65 offshore pipelines under cyclic global b
S79:E12

Probabilistic fatigue reliability assessment of girth-weld surface cracks in API 5L X65 offshore pipelines under cyclic global b

https://doi.org/10.3221/IGF-ESIS.79.07 Fatigue cracking at girth welds threatens offshore-pipeline integrity and requires uncertainty in flaw size, crack-growth behaviour, loading and weld geometry to be considered. A probabilistic fatigue-reliability framework is developed for a semi-elliptical surface crack in an API 5L X65 pipeline under cyclic global bending. Geometry-consistent stress-intensity-factor histories from a three-dimensional finite-element model provide 60 training and six case-wise held-out simulations. The Paris-law and loading distributions are identified as DNV code-calibrated benchmark inputs, not site-specific X65 measurements. For the fixed Paris exponent, normalisation by CeffΔσeq3 reduces the primary surrogate to a one-dimensional Gaussian process in initial crack depth. The model achieves R2 = 0.997 and MAPE = 4.04% on the test cases, and R2 = 0.996 with MAPE = 3.70% in leave-one-out validation. Using conditionally truncated inputs, the posterior-mean life distribution has a median of 6.84 × 108 cycles and a 95%-reliability design life of 2.12 × 108 cycles. Correlated latent-GP posterior-function propagation gives Pf = 4.147% at Nd = 2 × 108 cycles, with a 95% GP-posterior interval of 3.858–4.444%. Sensitivity analysis identifies the stress-range scale as dominant, showing that site-specific loading characterisation is essential for field application.

Front-resolved mode-II–III nominal driving-force evolution and group-validated machine-learning prediction for high-speed railwa
S79:E11

Front-resolved mode-II–III nominal driving-force evolution and group-validated machine-learning prediction for high-speed railwa

https://doi.org/10.3221/IGF-ESIS.79.06 Closed wheel-tread cracks can remain compression-dominated during rolling contact while sustaining substantial in-plane and out-of-plane shear. A sequential ABAQUS–FRANC3D–Python framework resolves this response over ten crack-geometry updates. A closure-aware nominal driving force combines event-paired differences in the mode-II and mode-III stress-intensity factors. Four arc-length descriptors summarise its front distribution: mean, peak, peak coordinate and coefficient of variation. Controlled comparisons evaluate initial crack size and orientation, axle load, speed and wheel–rail friction. Thirty Latin-hypercube finite-element conditions provide 4,272 front points for condition-grouped machine-learning validation. ExtraTrees achieves a case-macro cross-validation RMSE of 16.9587 MPa·mm1/2. Four held-out numerical conditions, comprising 579 front points, give a pointwise RMSE of 8.5794 MPa·mm1/2. Front coordinate and initial orientation have the largest mean absolute SHAP contributions. The predicted terminal profiles quantify differences in driving-force magnitude and localisation across conditions within the sampled domain.

Assessment of the effect of pre-impact loading on the residual strength and fatigue life of additively manufactured composite sa
S79:E10

Assessment of the effect of pre-impact loading on the residual strength and fatigue life of additively manufactured composite sa

https://doi.org/10.3221/IGF-ESIS.79.05 This study is dedicated to the investigation of the influence of the pre-impact loading on the residual properties of composite sandwich panels. The methodology was proposed for pre-impact testing followed by quasi-static and cyclic tension of structurally representative composite specimens and structural elements. The material was additively manufactured sandwich panels consisted of honeycomb core made of acrylonitrile butadiene styrene (ABS) thermoplastic and two load-bearing face sheets made of ABS reinforced with 15% carbon fibers. Novel experimental data was obtained on the residual load-bearing capacity and fatigue life after pre-impact loading at various impact energy. Several phenomenological models were used to approximate obtained data on impact sensitivity, that demonstrated high descriptive ability.

An interview with Liviu
S79:E09

An interview with Liviu

An interview with Liviu Marsavina during the ECF25 in Athens (2026) https://www.linkedin.com/in/liviu-marsavina-44741136/

An interview with Jianying
S79:E08

An interview with Jianying

An interview with Jianying He during the ECF25 in Athens (2026) https://www.linkedin.com/in/jianying-he-8721697/

An interview with Sara
S79:E07

An interview with Sara

An interview with Sara Bagherifard during the ECF25 in Athens (2026) https://www.linkedin.com/in/sara-bagherifard-0422a240/

An interview with Aabid
S79:E05

An interview with Aabid

An interview with Abdul Aabid during the ECF25 in Athens (2026) https://www.linkedin.com/in/dr-abdul-aabid-91514936/

Effect on mechanical properties, corrosion behaviour and fracture behaviour of FSWed AA 6061-T6 and AA 2024-T3 by using differen
S79:E04

Effect on mechanical properties, corrosion behaviour and fracture behaviour of FSWed AA 6061-T6 and AA 2024-T3 by using differen

https://doi.org/10.3221/IGF-ESIS.79.04 Friction Stir Welding (FSW) is widely validated as a solid-state joining process that has gained significant attention for the welding of aluminum alloys in aerospace and automotive applications. In this study, the effect of Tool Pin Profiles (TPP)—Taper Threaded (TTPP), Square (SPP), and Cylindrical Threaded (CTPP)—on the flow of material, mechanical properties, corrosion properties and microstructure of dissimilar aluminum alloys AA6061-T6 and AA2024-T3 was investigated. A Taguchi L9 orthogonal array (OA) was employed for the optimization of process parameters, which included Tool Pin Profile (TPP), Tool Rotational Speed (TRS) of 600, 700, and 800 rpm and Welding Speed (WS) of 25, 30, and 35 mm/min. Mechanical properties were evaluated in terms of Ultimate Tensile Strength (UTS), Stir Zone (SZ) microhardness, and Percentage elongation. Microstructural characterization was conducted using optical microscopy and Scanning Electron Microscopy (SEM). Post weld performance was evaluated using potentiodynamic polarization and immersion corrosion tests. The TTPP condition yielded the highest measured UTS (210 MPa), SZ microhardness (162 HV), and elongation (8.89%) within the tested parameter range. This performance is attributed to improved material mixing, refined grain structure, and a favourable thermal cycle during processing. Through Taguchi optimization analysis, it was confirmed that the most favorable conditions for joining AA6061-T6 and AA2024-T3 alloys are provided by the TTPP.

Study on mechanical, corrosion and fractured surface of n-Mn modified Al5052 alloy: an ANOVA and ANN prediction of wear rate
S79:E03

Study on mechanical, corrosion and fractured surface of n-Mn modified Al5052 alloy: an ANOVA and ANN prediction of wear rate

https://doi.org/10.3221/IGF-ESIS.79.03 Aluminum (Al) 5052 alloys are extensively utilized in marine environments, pressure vessels, and automotive parts due to their better strength and low density. However, more investigation is required to comprehend how the nanoscale manganese (n-Mn) element affects their mechanical, tribological, corrosion, and machinability. The development of Al5052 alloy modified with n-Mn by increasing the weight percentage in 0.25% increments from 0 to 1% through stir casting is the main focus of this study. The nano-composite showed notable improvements in hardness (23.72%), tensile strength (11.01%), and corrosion resistance (57.69%). However, increasing the n-Mn content also led to a 77.35% increase in machining force and a 69.23% increase in surface roughness (Ra). Taguchi and ANOVA approaches were used to analyze the effects of n-Mn (wt. %), sample temperature (ºC), and sliding distance (m) on wear loss (g). The improved alloy’s wear rate was largely influenced by its n-Mn concentration. Wear rate confirmation tests showed that maximum errors for the n-Mn modified Al5052 alloy were within permissible bounds. Additionally, the wear loss was successfully predicted using the proposed 3-4-1 Artificial Neural Network (ANN) model. For the wear attributes taken into consideration, the predicted performance metrics produced mean squared errors (MSE) of 4.925*10-5 and R-squared values (R2) of 0.9361.

Dominant crack selection in multi-crack stress corrosion cracking of AISI 316L stainless steel under sustained loading in flowin
S79:E02

Dominant crack selection in multi-crack stress corrosion cracking of AISI 316L stainless steel under sustained loading in flowin

https://doi.org/10.3221/IGF-ESIS.79.02 Stress corrosion cracking (SCC) in structural components often involves the simultaneous development of multiple cracks; however, the mechanism by which a dominant crack emerges under sustained loading remains insufficiently resolved. This exploratory study investigates competitive multi-crack SCC behavior in AISI 316L stainless steel under sustained tensile loading in flowing 1 M HCl. Five naturally nucleated surface cracks formed around a central hole were monitored using repeated in situ optical imaging. Interval-based crack growth rates (Δa/Δt) were calculated from five discrete inspection times. Post-test fracture paths were analyzed, supported by SEM fractography and SEM–EDS to assess localized degradation. Fracture-path analysis showed that Cracks 3 and 4 controlled the final trajectory. Interval-based descriptors identified Crack 4 as kinetically dominant within the tested specimen, exhibiting the highest mean and maximum growth rates and the largest cumulative extension. SEM–EDS revealed localized degradation, secondary branching, higher oxygen content, and a detectable chlorine signal in the Crack 4 region. Within the tested multi-crack configuration, dominant-crack behavior could be distinguished using interval-based growth descriptors from discrete observations. The findings are consistent with a combined influence of stress redistribution and localized corrosion-assisted degradation and provide a proof-of-concept basis for comparing crack-growth persistence from discrete observations.