The proposition of analytical expression HM–(√P/S) in microindentation pile-up deformation mode

Samir Habibi; Djamel Zddine Semsoum; Soufiane Benaissa; Hassen Merzouk

doi:10.3221/IGF-ESIS.60.28

The proposition of analytical expression HM–(√P/S) in microindentation pile-up deformation mode

Authors

Samir Habibi Laboratory of Industrial Engineering and Sustainable Development (LGIDD, Department of Mechanical Engineering, Ahmed Zabana University of Relizane, 48000, Algeria.
Djamel Zddine Semsoum LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.
Soufiane Benaissa LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.
Hassen Merzouk LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.

DOI:

https://doi.org/10.3221/IGF-ESIS.60.28

Keywords:

Microindentation, Martens hardness, Pile-up, Empirical, Cu99

Abstract

In this article, the characteristic curves of microindentation measured on Cu99 were analyzed on the basis of the analytical expression proposed by Habibi et al. (J. Mater. Res, 2021, 36 (15): 3074-3085). It was found that the ratio of the applied load to the square of the displacement, P/(h+h₀)², does not remain constant during the loading segment of the microindentation test. An empirical expression for the determination of Martens hardness as a function of indentation load, contact stiffness and reduced modulus of elasticity by analyzing indentation load curves has been proposed for pile-up mode strain with the corrections imposed by the tip defect, the compliance of the instrument and the axial axisymmetry coefficient of the Vickers indenter. The results from microindentation tests on this examined ductile material show excellent agreement.

Downloads

Download data is not yet available.

Author Biographies

Samir Habibi, Laboratory of Industrial Engineering and Sustainable Development (LGIDD, Department of Mechanical Engineering, Ahmed Zabana University of Relizane, 48000, Algeria.

Laboratory of Industrial Engineering and Sustainable Development (LGIDD,

Department of Mechanical Engineering,

Ahmed Zabana University of Relizane, 48000, Algeria.

Corresponding author: habibismr@yahoo.com
Djamel Zddine Semsoum , LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.

LGIDD, Department of Mechanical Engineering,

Mustapha Stambouli University of Mascara, 29000, Algeria.
Soufiane Benaissa , LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.

LGIDD, Department of Mechanical Engineering,

Mustapha Stambouli University of Mascara, 29000, Algeria.
Hassen Merzouk , LGIDD, Department of Mechanical Engineering, Mustapha Stambouli University of Mascara, 29000, Algeria.

LGIDD, Department of Mechanical Engineering,

Mustapha Stambouli University of Mascara, 29000, Algeria.

Downloads

Visual Abstract

Published

25-03-2022

Issue

Vol. 16 No. 60 (2022): April 2022

Section

Advanced Manufacturing and Surface Treatment

License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Copyright
Authors are allowed to retain both the copyright and the publishing rights of their articles without restrictions.

Open Access Statement

Frattura ed Integrità Strutturale (Fracture and Structural Integrity, F&SI) is an open-access journal which means that all content is freely available without charge to the user or his/her institution. Users are allowed to read, download, copy, distribute, print, search, or link to the full texts of the articles in this journal without asking prior permission from the publisher or the author. This is in accordance with the DOAI definition of open access.

F&SI operates under the Creative Commons Licence Attribution 4.0 International (CC-BY 4.0). This allows to copy and redistribute the material in any medium or format, to remix, transform and build upon the material for any purpose, even commercially, but giving appropriate credit and providing a link to the license and indicating if changes were made.

How to Cite

The proposition of analytical expression HM–(√P/S) in microindentation pile-up deformation mode. (2022). Frattura Ed Integrità Strutturale, 16(60), 407-415. https://doi.org/10.3221/IGF-ESIS.60.28